Using a different ougoing SIP provider with Callcentric

<< < (3/5) > >>

azrobert:
On the OBi200#2

Physical Interfaces -> Phone port
Add to beginning of the OutboundCallRoute:
{(<510111111*>@@.):pp},

Physical Interfaces -> Phone port -> DigitMap
Add AFTER the beginning parenthesis:
@@.S3|
 
Replace 510111111 with the OBi number Of OBi200#1                 

On the OBi200#1

Voice Services -> OBiTalk Service
Replace InboundCallRoute:
{510222222>0:ph},{510222222>(@@.):sp1},{ph}

Replace 510222222 with the OBi number Of OBi200#2

Dial 0 to ring the phone port on OBi200#1
Any other number will be routed to SP1 on OBI200#1

You weren't specific enough on the dialed numbers, so I allowed anything including a plus sign.
@@. will allow any character string.
The S3 after the @@. is a 3 second wait after the number is dialed.
This is to prevent the number being sent prematurely if you pause between numbers.
If you have a phone where you dial the number then press Talk/Send you can change it to S1 for a 1 second wait.

Shiblee:
Thanks. I am not sure of the digits also as the length of digits are different. I will be working on it later.

azrobert:
{(<510111111*>@@.):pp}

FYI when you call a remote OBi the format is:
Destination_OBi * Number : OBiTalk_Network
The * and Number are optional
pp is the ObiTalk network

@@. is checking for any dialed number.
If it matches the dialed number (which it will) then <510111111*> will prefix the number with the destination OBi number and a star.
If you dial 0 then 510111111*0 will be sent to the OBiTalk network.


Receiving a call:
{510222222>0:ph},{510222222>(@@.):sp1},{ph}

Format:
Sending OBi number > dialed number : destination

Shiblee:
Quote from: Shiblee on January 13, 2015, 07:38:37 pm

It is in Asia, calls are 9-15 digit (Local/international excluding + or 00).

1. OBi200 (1) has a ip telephone connection (SP1) & attached phone PH1.
2. OBi200 (2) has only attached phone PH1.

#1. Make calls through OBi200 (1) SP1 directly from OBi200 (2) attached PH1 to phone network. I need also call to attached phone of Obi200 (1).

#2. All incoming calls  at OBi200 (1) SP1 will be routed to OBi200 (2). I got answer,
Voice Services -> SP1 Services -> X_InboundCallRoute
The default is: ph >> Change it to: pp(OBI200 (2) NO)

Thanks.


I tested the setup today with ipte.org accounts. for case #2 calls from SP1 (OBi200- 1) forwarded to  (OBi200- 2) but auto attended recieving call. I have changed
Voice Services -> OBitalk ->InboundCallRoute-> ph.

Now, I am getting call but no caller ID. How to get CID?

azrobert:
The CID should automatically be passed when using the OBiTalk network.
Can you check the call history on OBI200-1 to see if you are receiving a CID.
Does the CID have any special characters like a plus sign?
Some phone will not display CID when it contains special characters.

To access Call History:
Log directly into the OBi using the local interface.
Key the IP address of the OBi into a Web Browser.
Hit Enter
The UserID and default Password are both "admin".
Click Status on the left column.
Then click Call History.

Navigation

[0] Message Index

[#] Next page

[*] Previous page