OBi110, POTS, and GV
azrobert:
Sorry, my mistake. You wrote "exchanges" and my brain read "area codes".
Service Providers -> ITSP Profile A General -> DigitMap:
(1xxxxxxxxxx|[2-9]xxxxxxxxx|011xx.)
Physical Interfaces -> Phone Port -> DigitMap
Add AFTER the beginning parenthesis: (Mli)|
It will look like this:
((Mli)|.....the current settings....)
Physical Interfaces -> Phone Port -> OutboundCallRoute
Add to the beginning: {(Mli):li},
Physical Interfaces -> Phone Port -> Primary Line: SP1 Service
Physical Interfaces -> Line Port -> DigitMap
(xxxxxxx|207(234|456|789)xxxx|18(00|88|77|66|55|44)xxxxxxx)
The above config (911 is handled separately) will do this:
911, 7 digit, 10 digit for exchanges 234/456/789 within area code 207 and tollfree numbers routed out Line.
Other 10 digit numbers, 11 digits and international numbers will be routed out SP1.
UncleOp:
Quote from: azrobert on October 13, 2014, 01:04:22 pm
Sorry, my mistake. You wrote "exchanges" and my brain read "area codes".
:
I understand that... :-)
Quote
:
The above config (911 is handled separately) will do this:
911, 7 digit, 10 digit for exchanges 234/456/789 within area code 207 and tollfree numbers routed out Line.
Other 10 digit numbers, 11 digits and international numbers will be routed out SP1.
Nice. Will GV simply get and place the call? Or will it still call me back? (yeah, I could try it, but I figured I'd ask.)
azrobert:
The call will go out directly.
Quote
"How do I get my OBiON-enabled smartphone to connect via WiFi to make calls through my OBi110?"
In the Nexus5 did you setup a WiFi connection to your router?
In OBi Expert
Voice Services -> OBiTalk Service -> InboundCallRoute: ph
The above is the default setting. The OBi setup process might have altered this setting.
Dial any number on the OBiON app.
The OBi110 phone port should ring.
This is to test if the OBiON app is communicating with the OBi110.
The next step will be to setup inbound and outbound calls.
Do you know how to use OBi Expert?
UncleOp:
Quote from: azrobert on October 13, 2014, 01:25:09 pm
The call will go out directly.
Cool beans.
Quote
Quote
"How do I get my OBiON-enabled smartphone to connect via WiFi to make calls through my OBi110?"
In the Nexus5 did you setup a WiFi connection to your router?
I know my Nexus can and does use WiFi for browser, etc. I don't recollect doing any voice-call-related changes for it, however.
Quote
In OBi Expert
Voice Services -> OBiTalk Service -> InboundCallRoute: ph
The above is the default setting. The OBi setup process might have altered this setting.
Dial any number on the OBiON app.
The OBi110 phone port should ring.
This is to test if the OBiON app is communicating with the OBi110.
The next step will be to setup inbound and outbound calls.
Do you know how to use OBi Expert?
I have used OBi Expert to enable syslog, and I do get some periodic messages from the device on my daemon. I will likely take the full plunge this weekend when I have some hours free to hack and debug. I'll make sure I save a backup of my current config, of course.
Thanks for your help!
azrobert:
I already had these instructions for OBi Expert:
From the OBiTalk dashboard click Edit Profile on the left column.
At the bottom of the page check "Enable Obi Expert..."
Click Submit Query.
Now you can go directly to OBi Expert from the dashboard.
Click Obi Dashboard.
On the right of your OBi110 is an icon with a red E.
Click on it to enter OBi Expert.
To navigate click on the titles with the +
Then click on a sub-title
An example click on Service Providers
Then click ITSP Profile A General
There 2 boxes to the right of each setting
To change a setting uncheck the box under ObiTalk Setting
Then uncheck the box under Device Default
Now change the setting
After you have made all the necessary changes for that page, click Submit at the bottom of the page.
OBiTalk will download the configuration changes to the OBi110 and reboot it.
Wait until this process is complete before continuing to the next page.
Navigation
[0] Message Index
[#] Next page
[*] Previous page