Use OBi110 without a network connection
drgeoff:
I can confirm that my OBi110 (2824 fw) behaves the same as reported by azrobert. Mine also has manually assigned IP addresses and is configured via its inbuilt web server.
Are you certain that you are attempting to call out via the LINE port and not via VoIP?
PeSiw:
I have set up a short, repeatable, configuration and test that I have used to demonstrate the problem ...
SUMMARY
I have provided the OBi110 Product Information
I have provided a short Procedure that I have followed that gives repeatable results.
I have provided 5 simple Tests that demonstrate the symptoms I have observing.
PRODUCT INFORMATION
ModelName OBi110
SerialNumber 88B01NAZZxxx
OBiNumber 200 052 xxx
HardwareVersion 3.4
SoftwareVersion 1.3.0 (Build: 2824)
SystemTime 16:01:09 01/01/2010, Friday
UpTime 0 Days 0:01:09 (13)
CertificatesStatus Installed
CustomizationStatus Generic
PROCEDURE
Power up OBi110
After power up is complete, press and hold hardware reset button on the bottom of the box for ~12 seconds (until Power LED goes out)
Log in to OBi110 at DHCP provided IP address. Settings ...
WAN Status
AddressingType DHCP
IPAddress 192.168.1.81
SubnetMask 255.255.255.0
DefaultGateway 192.168.1.254
DNSServer1 192.168.1.254
DNSServer2
MACAddress 9CADEF012xxx
Setup static IP (below), Submit and Reboot. Settings ...
WAN Status
AddressingType Static
IPAddress 192.168.1.81
SubnetMask 255.255.255.0
DefaultGateway 192.168.1.1
DNSServer1 192.168.1.1
DNSServer2
MACAddress 9CADEF012xxx
TEST 1 - Call phone to line with network connected with static IP
Dial local 10 digit number on a standard phone connected to the Phone port.
After the delay built into the default settings (~20 sec) the called phone rings, lifted off-hook and the call is connected.
Hang up the phone, call is completed.
DISCONNECT OBi110 FROM NETWORK
Remove power from the OBi110
Remove the ethernet cable from the OBI110
Power up the OBI110
After the power up cycle is completed, the ...
Power LED is flashing green
Network LED is off
Phone LED is off
Line LED is solid green.
TEST 2 - Call phone to line with network disconnected and power led on when phone goes off-hook
Dial local 10 digit number on a standard phone connected to the Phone port ... going off hook when the power led is ON (green) ...
After the delay built into the default settings (~20 sec) the IVR reports ... "Network status ... IP address not available ... please review FAQ ... reason 00".
TEST 3 - Call phone to line with network disconnected and power led off when phone goes off-hook
Dial local 10 digit number on a standard phone connected to the Phone port ... going off hook when the power led is OFF...
After the delay built into the default settings (~20 sec) the called phone rings, lifted off-hook and the call is connected.
Hang up the phone, call is completed.
TEST 4 - Call phone to line with network disconnected and power led on when phone goes off-hook
Dial local 10 digit number on a standard phone connected to the Phone port ... going off hook when the power led is ON (green) ...
After the delay built into the default settings (~20 sec) the IVR reports ... "Network status ... IP address not available ... please review FAQ ... reason 00".
TEST 5 - Call phone to line with network disconnected and power led off when phone goes off-hook
Dial local 10 digit number on a standard phone connected to the Phone port ... going off hook when the power led is OFF ...
After the delay built into the default settings (~20 sec) the called phone rings, lifted off-hook and the call is connected.
Hang up the phone, call is completed.
...
PeSiw:
I received this as a ticket response ...
...
This is a known issue that has been resolved.
Please login to obitalk.com and do "ADD DEVICE", and follow all the steps.
Your OBi firmware would be updated to the latest one, which resolves the issue that you see.
Afterwards, you can set it up with static IP and disconnect it from the internet.
...
Is there a newer version of the firmware than 1.3.0 (Build: 2824)? If so, where can I find it?
giqcass:
The newest I am aware of is
OBi110-1-3-0-2868.fw
http://fw.obihai.com/OBi110-1-3-0-2872.fw
I don't know if it's production release.
PeSiw:
This firmware fixes the problem ... thanks giqcass!
Navigation
[0] Message Index
[#] Next page
[*] Previous page