Setting-up OBI110 and OBI100 as Bridged and still allowing me to use GV

(1/3) > >>

artsmart:
Hi there!

I setup OBI110 on Point A and OBI100 on Point B following this instruction from RonR http://www.obitalk.com/forum/index.php?topic=2016.msg12745#msg12745 is there any possibility that I can integrate GV on this kind of setup? How?

azrobert:
I did not read thru the whole link you provided.
What do you want to do?
Do you just want to call the phone connected to the other OBi without using the OBiTalk network?
On both obi's what do you have defined on SP1 and SP2?

artsmart:
Current settings using instructions by RonR on this thread http://www.obitalk.com/forum/index.php?topic=2016.msg12745#msg12745. OBi100 can make and receive local calls thru the PSTN attached to OBi110 and I want to keep it that way. For me to make and receive International Calls, I'd like to setup GV on OBi100. Will this work with the current setup? If not, is there any other way?

azrobert:
You have 2 choices.

Choice#1
You can define the same GV account on both the OBi100 and OBi110.
Assuming GV is defined on SP1, in both OBi's phone port outbound call route add:
{(011xx.):sp1}

The last OBi connected will receive inbound calls.
In both OBi's SP1 InboundCallRoute send calls to the other OBi the same way you do Line calls.
Now it doesn't matter which OBi receives the call.

Choice#2
Define GV on the OBi100
Assuming GV is defined on SP1, in the OBi100 phone port outbound call route add:
{(011xx.):sp1}

In the OBi110 phone port outbound call route add:
{(011xx.):vg1}
VG1 points to the OBi100

In the OBi100 SP2 InboundCallRoute add: {>(011xx.):sp1}

In the OBi100 SP1 InboundCallRoute send calls to the OBi110 the same way you do Line calls

artsmart:
Hello Sir! Here's my current settings, in which part here should I add or modify so GV can be integrated:

1. Disable Auto Provisioning in each OBi:

System Management -> Auto Provisioning -> ITSP Provisioning -> Method : Disabled
System Management -> Auto Provisioning -> OBiTALK Provisioning -> Method : Disabled

2. Enable SIP in each OBi (SP2/ITSP Profile B):

Service Providers -> ITSP Profile B -> SIP -> ProxyServer : 127.0.0.1

Voice Services -> SP2 Service -> AuthUserName : (put anything here)
Voice Services -> SP2 Service -> X_RegisterEnable : (unchecked)
Voice Services -> SP2 Service -> X_ServProvProfile : B

3. Set Voice Gateway 1 in each OBi to point to the other OBi:

Voice Services -> Gateways and Trunk Groups -> Voice Gateway1
Name : OBi
AccessNumber : SP2(w.x.y.z:5061)

where w.x.y.z is the IP address of the other OBi.

4. Set the LINE Port in OBi110 to bridge incoming calls to OBi100:

Physical Interfaces -> LINE Port -> InboundCallRoute : {vg1,ph}

Remove ,ph if you don't want the phone connected to OBi #1 to ring on incoming calls.

5. Set the SP2 Service in OBi110 to bridge incoming calls to the LINE Port:

Voice Services -> SP2 Service -> X_InboundCallRoute : {>(Mli):li}

6. Set the PHONE Port in OBi100 to bridge calls to OBi11o:

Physical Interfaces -> PHONE Port -> OutboundCallRoute:

{([1-9]x?*(Mpli)):pp},{(<#:>|911):li},{**0:aa},{***:aa2},{(<**1:>(Msp1)):sp1},
{(<**2:>(Msp2)):sp2},{(<**8:>(Mli)):li},{(<**9:>(Mpp)):pp},{(Mpli):vg1}

Navigation

[0] Message Index

[#] Next page