Call Forward (unconditional) & dialling out on Obitalk 200 ---Help needed.
realjohny:
I will try now with PBXES but can AA help me to have dial rules? Like:
1- Calling remote Obi and getting a dial tone of PSTN and/or use remote BT phone ?
2- Call phone connected with local Obi and then getting call transferred to remote Obi and do the above number 1 ?
3- Getting all calls on remote ObiBT transferred to local Obi and then via local ObiBT to my mobile ...unconditionally ?
Thanks a lot :)
azrobert:
The AA can only route a call to a trunk.
An inbound call can be routed to the AA unconditionally or by callerid.
The following assumes PBXes is defined on SP1 on local and the remote OBi.
This is how it would work:
Quote
2- Call phone connected with local Obi and then getting call transferred to remote Obi and do the above number 1 ?
You want to dial number 123456 on the remote PSTN or get dial tone.
You call the local BT phone.
You are sent to the AA.
You will get a prompt
You enter 2 for a new call
You will get another prompt for the outbound number
You enter 9123456 or 9
I chose the 9 prefix
The call is sent to SP1 (PBXes) because the AA primary route is SP1
The remote OBi will receive the call on SP1 with the dialed number.
The SP1 X_InboundCallRoute will have rules based on the 9 prefix to send 123456 to PSTN or get PSTN dial tone
Quote
3- Getting all calls on remote ObiBT transferred to local Obi and then via local ObiBT to my mobile ...unconditionally ?
You can do this without the AA
Quote
1- Calling remote Obi and getting a dial tone of PSTN and/or use remote BT phone ?
Yes, but I don't understand how are you calling the remote OBi?
azrobert:
Here is an example how PBXes can route a phone number to an OBi.
http://www.obitalk.com/forum/index.php?topic=5411.0
In this example the iPhone is registered as an extension and the OBi as a Sub-PBX. The iPhone is sending outbound numbers to the OBi.
You want to send outbound numbers in both directions, so both OBi's will be setup as a Sub-PBX.
The above post is almost 2 years old and that is the last time I used PBXes, so I have to refresh my memory on how Sub-PBXes work.
realjohny:
I tried PBXES on Bria for Andriod and PC but voice quality is worst ever and latency is very high, in fact you can't recognize each other.
As I am in VoIP censored area on both local and remote site and good thing is that GV and Obitalk works, though GV quality is better. Can you please help me to configure local and remote devices (step by step with syntax/dialing rules?) using AA or a direct way to achieve it. I will try yo summarize again what I want to achieve:
1- I want to receive all remote calls from remote ObiBT/Obi/GV/Other VoIP provider (in another country) on local Obi (paired with a mobile phone) and then transferred to my mobile which I carry with me anywhere.
2- I want to call local ObiBT and then reach remote ObiBT and remote ObiLine to call out.
3- I want to be able to call remote Obi sometime using local obi (either Obi-Obi Or GV-GV or other SIP-SIP), speed dials will help.
Thank you very much. :)
azrobert:
I'm leaving shortly and will be back in a few hours.
I don't have time to re-read this thread to see what we did.
Is the last post your complete requirements or do you also need something we did previously?
Navigation
[0] Message Index
[#] Next page
[*] Previous page