OBI110: Disconnect Tone Pattern
202Owner:
Quote from: malomyasa on February 20, 2015, 11:22:42 am
I'm sorry that I misled you in my first message.
String "480-30,620-30;10;(.25+.25)" - this is OBI's default parameter - has been used only for example.
What you said that was misleading is "My OBI110 sometimes suddenly ends calls."
Now it turns out you are quite experienced and are trying to hack the OBi110 into your PBX application, and you are expecting people to waste their time trying to understand your application that you are unwilling to explain in advance of seeking their help. And you can't be bothered to read the referred admin guide that answers your initial question. Good luck.
malomyasa:
1. "My OBI110 sometimes suddenly ends calls" - exactly.
2. Misleading is: "Parameter Line->DisconnectTonePattern = 480-30,620-30;10;(.25+.25)"
3. About what hacks are you saying? FXO-gateway - one of the modes OBI110, implemented by the developers. Why should not I use it?
4. I spent a few days in search of information about the parameter DisconnectTonePattern - to no avail. You have given me the information - where to read. Thanks You. But in the Admin Guide also no information about the parameter DisconnectTonePattern. There is information on how to configure Busy Tone - but it's not the same thing.
And finally - I did not ask me to help. I asked a simple question, expecting to get a simple answer. ianobi gave me an answer. Thanks very much to him.
That's all. Good Luck.
FabioCarloni:
Hi,
the disconnect tone in Italy is 425 Hz, 0.2s ON + 0,2s OFF.
then
DisconnectTonePattern = 425-30;10;(.2+.2)
Often the calls are cut.
I also tried
425-30;10;5(.2+.2)
425-30;10;1(1/.2+.2,1/.2+.2,1/.2)
the problem still remains!
azrobert:
The disconnect tone works when the other party hangs up, so it is working correctly.
Why would a disconnect tone of any duration be generated when a call is in session?
I know you said the problem doesn't occur when the disconnect tone is disabled, but it could be another problem.
Are you at the current firmware level on the OBi110?
FabioCarloni:
Quote from: azrobert on May 14, 2015, 09:33:27 am
The disconnect tone works when the other party hangs up, so it is working correctly.
Why would a disconnect tone of any duration be generated when a call is in session?
I know you said the problem doesn't occur when the disconnect tone is disabled, but it could be another problem.
Are you at the current firmware level on the OBi110?
I know how a tone disconnection. I don't know why the tone is generated during the session. If the disconnect tone is disabled, the problem disappears.
I tried it with 3 different devices obi 110, same problem. I have no problem with Grandstream HT-503 and Cisco SPA3102.
This is the log of the obi
Code:
2015-05-23 16:30:52 debug 192.168.7.41 kern FXO ONHOOK MONITOR
2015-05-23 16:30:52 debug 192.168.7.41 kern FXO NewTermState:onhook
2015-05-23 16:30:52 debug 192.168.7.41 kern FXO ONHOOK MONITOR
2015-05-23 16:30:52 debug 192.168.7.41 kern call overall status -- peer: 192.168.7.50:10182, local: 192.168.7.41:16810, pkt_tx: 3036, pkt_rx: 3001, bytes_tx: 522192, bytes_rx: 516172, clk_diff: -319 PPM, pkt_in_jb: 9, pkt_ooo: 0, pkt_lost: 0, pkt_late: 0, pkt_loss_rate: 0 %, pkt_drop_rate: 0 %, jb_len: 170 ms, curr_rcvd_jitter: 2 ms, rcvd_digits: 0, underruns: 0, overruns: 0, seq_num_broken: 0, pkt_interp: 67, skew_comp: 0 ms, frm_in_pkt: 2
2015-05-23 16:30:52 debug 192.168.7.41 kern RTP Del Channel
2015-05-23 16:30:52 debug 192.168.7.41 kern FXO tell cc end-call
2015-05-23 16:30:52 debug 192.168.7.41 kern DAA Disc.Tone 0 0
2015-05-23 16:30:52 debug 192.168.7.41 kern DAA Disc.Tone 0 0
2015-05-23 16:29:58 debug 192.168.7.41 kern RTP Del Channel
2015-05-23 16:29:58 debug 192.168.7.41 kern SIP DLG reject: 503
2015-05-23 16:29:58 debug 192.168.7.41 kern FXO make new call
2015-05-23 16:29:51 debug 192.168.7.41 kern FXO ring off
2015-05-23 16:29:51 debug 192.168.7.41 kern RTP Start->c0a80732:10182(80);0;0;0:0:0;0(50)
2015-05-23 16:29:51 debug 192.168.7.41 kern FXO Stop Tone
2015-05-23 16:29:51 debug 192.168.7.41 kern FXO NewTermState:offhook
2015-05-23 16:29:51 debug 192.168.7.41 kern FXO OFFHOOK
2015-05-23 16:29:51 debug 192.168.7.41 kern fxo cp answered
2015-05-23 16:29:51 debug 192.168.7.41 kern RTP DtmfTxMtd:1(1),0
2015-05-23 16:29:49 debug 192.168.7.41 kern DAA CND ,3385800120,,,,
2015-05-23 16:29:49 debug 192.168.7.41 kern DAA CND ,3385800120,,,,
2015-05-23 16:29:49 debug 192.168.7.41 kern ------ caller id (pcm_id: 1) received! ------------
2015-05-23 16:29:48 debug 192.168.7.41 kern FXO NewTermState:ringing
2015-05-23 16:29:48 debug 192.168.7.41 kern Ring On
What is "DAA Disc.Tone 0 0"? Why is it generated?
I tried different codecs, G.729 and G.711, but this is not the solution.
P.S. OBI 110 Software Version: 1.3.0 (Build: 2872)
Navigation
[0] Message Index
[*] Previous page