One way audio with Obi202, Panasonic KX-TGP550T04 and double NAT
Zopa:
azrobert, I'm trying your suggestions, but I'm a bit lost as this is a novel thing for me.
This part worked fine:
Quote
Voice Services -> Gateways and Trunk Groups -> Trunk Group 1
TrunkList: sp1,sp2,sp3
DigitMap: (Msp1)
X_InboundCallRoute: {123456789>(Mtg1):tg1}
And so did this:
Quote
I have GV defined on SP1 and set MaxSessions=1
Now I can only place one outbound call, which goes out on SP1
However, the rest of the instructions are just a tad confusing to me. Can you expand on them a bit? What do you mean by this? Quote
Define ITSP A, B and C DigitMap with the same rules.
Under Service Providers -> ITSP Profile X General -> DigitMap, I have a default value of "(1xxxxxxxxxx|<1>[2-9]xxxxxxxxx|011xx.|xx.|(Mipd)|[^*#]@@.)" Is this what you're you suggesting I change? I'm not exactly sure.
To tell you the truth I'm not very handy with regular expressions of DigitMap syntax yet. Yes, I looked at the manual, but it still looks like Greek to me. :)
Also this sentence is not very clear to me either. Quote
If you are calling from the Phone Port change the Primary Line to TG1.
Thank you in advance.
azrobert:
The OBi MaxSessions is different than the GV MaxSessions. Each inbound or outbound call will use 1 session. If you have MaxSessions set to 1 on SP1 with an active outbound call, you won't be able to receive an inbound call. That is my understanding. If you want to have SP1 open for inbound calls, you can place it 3rd in the Trunk Group.
I will respond to your last post latter. I don't have time right now.
azrobert:
I probably shouldn't have said anything because the default settings will work, but you should understand how trunk groups work. I guess I did a poor job of explaining.
This is how a Trunk Group works
The 1st trunk in the TG is SP1
The dialed number is compared to the ITSP A DigitMap
If the dialed number matches a rule in the DigitMap the call is routed out SP1.
If there is a mismatch SP1 is skipped and the same process is used for ITSP B DigitMap and SP2
This is repeated for each trunk in the TG list until the call is routed.
I didn't include the failover process.
All the ITSP X DigitMaps contain the rule "xx.", so the defaults will work and no change is required.
If you have an analog phone(s) connected to the Phone Port(s) make the following change(s)
Physical Interfaces -> Phone1 Port -> Primary Line: Trunk Group 1
Physical Interfaces -> Phone2 Port -> Primary Line: Trunk Group 1
Zopa:
Thank you azrobert. Just a quick point of clarification. I don't care for inbound calls via Obi at all. Inbound calls are not routed via Obi (at least they weren't before), but rather are going via a ipcomms.net free DID proxying to my callwithus.com account and ring directly on my KX-TGP550T04. However now I question if this setup would work quite like this since I have Obi in the mix, registering to GB account. I wonder if I can uncheck it as an available "phone" in GV web interface.
What would seem as ideal setup for me would be to have first outbound call to go on SP1, taking 1 of 2 of GV channels, and any subsequent calls to go on SP2 GV channels, then SP3 GV channels. That would give me up to 5 concurrent outbound calls, and between one and two of
azrobert:
Quote
I wonder if I can uncheck it as an available "phone" in GV web interface.
Yes, you can. Then inbound calls will only go to your CallWithUs account.
Navigation
[0] Message Index
[#] Next page
[*] Previous page