Outbound call route (Dial Plan)

<< < (2/4) > >>

Riyas:
RonR,

Thanks to your help, my dial plan was working good. I wanted to set up your single stage method (http://www.obitalk.com/forum/index.php?topic=1103.0).

This is my obitalk inboundcall settings :

{(Mcot)>(Mli):li},{(Mcot)>(<*1:>(Msp1)):sp1},{(Mcot)>(<*2:>(Msp2)):sp2},{(Mcot)>(<*3:>(Mvg3)):vg3},{(Mcot)>(<*8:>(Mli)):li},{(Mcot)>(<*9:>(Mpp)):pp},{(Mcot)>(<**1:>(Msp1)):sp1},{(Mcot)>(<**2:>(Msp2)):sp2},{(Mcot)>(<**3:>(Mvg3)):vg3},{(Mcot)>(<**8:>(Mli)):li},{(Mcot)>(<**9:>(Mpp)):pp},{(Mcot):aa},{ph}

I've also followed other steps (changing digitmap and inboundcall route in Phone and Auto attendant, creating new user defined digitmaps etc...)

Since then, if I dial 00919xx. to call indian mobile, my calls are routed through PSTN line instead of SP1.

My line port digitmap is : (<**1>00919xx.|<**1>0097xx.|xx.)

I don't know if I have to change anything. Thanks for your help

RonR:
I'm assuming we're discussing single-stage dialing here and calls from the PHONE Port are still working properly...

I think you'll need to add the following rule to the beginning of your OBiTALK InboundCallRoute to have single-stage dialing mimic your PHONE Port behavior:

{(Mcot)>(00919xx.|0097xx.):sp1},

Riyas:
Actually Yes, I am trying to setup single stage dialling. But as soon as I change phone port's and auto attendant's digitmap, all calls from PHONE port are routed through Line port (even 00919 calls). I am gonna try your method and keep you informed

Thanks

RonR:
The OBiTALK InboundCallRoute won't affect the PHONE Port (and neither will the Auto Attendant DigitMap).

What did you change in the PHONE Port and Auto Attendant DigitMap's?  The only thing you should have needed to change was:

In the PHONE Port and Auto Attendant DigitMap's, change [1-9]x?*(Mpli) to [1-9]x?*@@.

In the PHONE Port and Auto Attendant OutboundCallRoute's, change {([1-9]x?*(Mpli)):pp} to {([1-9]x?*@@.):pp}

Those changes shouln't have made any difference to PHONE Port calling of 00919 or 0097 numbers.  They still should go out SP1 instead of the LINE Port.

Riyas:
Quote from: RonR on October 24, 2011, 12:26:42 pm


In the PHONE Port and Auto Attendant DigitMap's, change [1-9]x?*(Mpli) to [1-9]x?*@@.

In the PHONE Port and Auto Attendant OutboundCallRoute's, change {([1-9]x?*(Mpli)):pp} to {([1-9]x?*@@.):pp}



These are exact changes I've made. As soon as I change these settings, all my calls are routed through PSTN (my PSTN dials **100919xxxxxxxx)

Call 6   10/24/2011    20:02:00   
Terminal ID                 PHONE1           LINE1
Peer Name      
Peer Number   009196008xxxxx   **1009196008xxxxx
Direction                  Outbound   Outbound
20:02:00   New Call   
20:02:09   Call Connected
20:02:11   End Call

But If I revert back to old settings ([1-9]x?*(Mpli) & {([1-9]x?*(Mpli)):pp} ), it's working again through SP1. It's strange

Navigation

[0] Message Index

[#] Next page

[*] Previous page