Need more help in Digimap

<< < (3/4) > >>

azrobert:
You also need this:
Voice Service -> Gateway & Trunk Grps -> Trunk Group1 -> DigitMap:
((Mpp)|(Msp1)|(Msp2))

OzarkEdge:
Quote from: azrobert on May 25, 2015, 09:39:49 pm

This is the setup:

Service Providers -> Voice Gateways -> Voice Gateway#1
Name: CallWithUs
AccessNumber: sp1(tf.callwithus.com)
DigitMap: (18(00|88|77|66|55|44)xxxxxxx)
AuthUserID: 2223334444

Voice Service -> Gateway & Trunk Grps -> Trunk Group1 -> TrunkList
pp,vg1,sp1,sp2

Change 222333444 to your CallerID.



This also works with CWU in lieu of setting AuthUserID:

Gateways and Trunk Groups - Voice Gateway1::AccessNumber = sp1(tf.callwithus.com;ui=callerID number)

And, you may need to add (Mvg1) to (Mtg1):

TG1 (Mtg1) = (...|(Mvg1)|...)

OE

azrobert:
Quote from: OzarkEdge on May 26, 2015, 01:02:08 pm

And, you may need to add (Mvg1) to (Mtg1):

TG1 (Mtg1) = (...|(Mvg1)|...)


(Msp2) has rule "1xxxxxxxxxx", so (Mvg1) is not needed in (Mtg1). It wouldn't hurt to include (Mvg1), but it would be redundant.

OzarkEdge:
Quote from: azrobert on May 26, 2015, 01:41:04 pm

Quote from: OzarkEdge on May 26, 2015, 01:02:08 pm

And, you may need to add (Mvg1) to (Mtg1):

TG1 (Mtg1) = (...|(Mvg1)|...)


(Msp2) has rule "1xxxxxxxxxx", so (Mvg1) is not needed in (Mtg1). It wouldn't hurt to include (Mvg1), but it would be redundant.


Understood.  I said 'may' because I wasn't going to check the whole dial plan.

I suggest that redundancy is perfectly acceptable/desirable if both trunks are to permit the same digits dialed.  I suggest that a trunk's digit map should be complete.  Then when you go to use it in the dial plan, it enables its trunk as it should without having to rely on rules spread around elsewhere that may or may not be in play... much easier to keep it simple and redundant, and to use user-defined digit maps to easily share the redundant rules.

I believe VG1 will ultimately not be used unless (Mvg1) permits the digits dialed.

OE

jtan:
Like to thank Robert and OE for you suggestions and ideas.   It took me a while to experiment these toll free number that will not accept calling from FPL.

1-800-213-8378 (USA only)
1-800-444-4444 MCI (USA only)

Using the trunk method :

Voice Service -- SP1 Service -- X_NoRegNoCall
check

Voice Service -- SP2 Service -- X_NoRegNoCall
check

Service Providers -> Voice Gateways -> Voice Gateway#1
Name:                         CallWithUs
AccessNumber:            sp1(tf.callwithus.com)
DigitMap:                     (18(00|88|77|66|55|44)xxxxxxx)
AuthUserID:                 320 123 4567

Voice Service -- Gateway & Trunk Grps -- Trunk Group1 -- TrunkList
pp,vg1,sp1,sp2

Voice Service -> Gateway & Trunk Grps -> Trunk Group1 -> DigitMap:
((Mpp)|(Msp1)|(Msp2))


Physical Interfaces  -- Phone1 -- OutboundCallRoute      
{([1-9]x?*(Mpli)):pp},{(<##:>):li},{**0:aa},{***:aa2},{222222222:pp},{(<**1:>(Msp1)):sp1},{(<**2:>(Msp2)):sp2},{(<**3:>(Msp3)):sp3},{(<**4:>(Msp4)):sp4},{(<**9:>(Mpp)):pp},{(Mtg1):tg1}


Reference

https://www.obitalk.com/forum/index.php?topic=8208.0

Navigation

[0] Message Index

[#] Next page

[*] Previous page