News:

On Tuesday September 6th the forum will be down for maintenance from 9:30 PM to 11:59 PM PDT

Main Menu

simulataneous calls

Started by skipro, July 16, 2011, 12:21:34 PM

Previous topic - Next topic

RonR

I'm not familiar with the 7960 or it dial plan syntax.  You probably want to set it up to transparently pass all digits and *'s.

bruss

#41
in order to pass caller-id info to the IP phone(VGWAYS) you take out the vg1(xyz) statement in the

{ph,vg1(7960),vg2(9642)}

inboundcallrouter on SP2 and replace it with


{ph,SP2(7960@10.10.10.202:5062),SP2(9642@10.10.10.201:5603)}

where 7960 and 9642 are the respective names of my ipphones.

Man what great support I have been getting from OBIHAI... I mean for a 60 dollar product it is just amazing.. I have thousand dollar routers and switches i get less support on..

Thanks for everything.. What a great product

RonR

Now, can you get them to fix the OBi so all this doesn't all fall apart if you enable Call Forwarding (*72) or Do Not Disturb (*78)?

If you enable Do Not Distrub (*78) to temporarily quiet the phones, all attempts to make outgoing calls from your 7960 and 9642 will result in a busy signal.

If you enable Call Forwarding (*72) to temporarily forward all incoming calls to your cell phone, all attempts to make outgoing calls from your 7960 and 9642 will result in those calls going to your cell phone.

QBZappy

Quote from: bruss on July 28, 2011, 07:14:21 PM
in order to pass caller-id info to the IP phone(VGWAYS) you take out the vg1(xyz) statement in the

{ph,vg1(7960),vg2(9642)}

inboundcallrouter on SP2 and replace it with


{ph,SP2(7960@10.10.10.202:5062),SP2(9642@10.10.10.201:5603)}

Isn't there a typo in there. 5603 should be 5063?

CID passes because it is an ip phone?
Owner of the 1st OBi110/100 units in service in Canada & South America. 1st OBi202 on my street. 1st OBi1032 in Montreal.

RonR

Quote from: bruss on July 28, 2011, 07:14:21 PM
in order to pass caller-id info to the IP phone(VGWAYS) you take out the vg1(xyz) statement in the

{ph,vg1(7960),vg2(9642)}

inboundcallrouter on SP2 and replace it with


{ph,SP2(7960@10.10.10.202:5062),SP2(9642@10.10.10.201:5603)}

where 7960 and 9642 are the respective names of my ipphones.

Am I correct that you also have?:

Service Providers -> ITSP Profile B -> SIP -> X_SpoofCallerID : (checked)

This method does work, although it souldn't be necessary.  I hope Obihai intends to fix Voice Gateway operation as it's much cleaner to have the IP addresses in one place rather than four.

RonR

Quote from: QBZappy on July 28, 2011, 07:54:35 PM
CID passes because it is an ip phone?

No, this method works because there's a problem with CallerID handling through Voice Gateways.

QBZappy

Quote from: RonR on July 28, 2011, 09:01:27 PM
Quote from: QBZappy on July 28, 2011, 07:54:35 PM
CID passes because it is an ip phone?

No, this method works because there's a problem with CallerID handling through Voice Gateways.

What problem?
Owner of the 1st OBi110/100 units in service in Canada & South America. 1st OBi202 on my street. 1st OBi1032 in Montreal.

RonR

Quote from: QBZappy on July 28, 2011, 09:03:56 PM
Quote from: RonR on July 28, 2011, 09:01:27 PM
Quote from: QBZappy on July 28, 2011, 07:54:35 PM
CID passes because it is an ip phone?

No, this method works because there's a problem with CallerID handling through Voice Gateways.

What problem?

A bug, an omission, a design flaw, only Obihai knows.  CallerID is not being passed when a Voice Gateway is used.

QBZappy

RonR,

Be patient until V 1.3 comes out. Until now, CID fix is one of the few carrots that OBi has ever offered the OBi user in advance. They have delivered on promised features/fixes in the past. I don't doubt that they will not fix it. Until then, passing CID  is a known problem.
Owner of the 1st OBi110/100 units in service in Canada & South America. 1st OBi202 on my street. 1st OBi1032 in Montreal.

bruss

yeah i have a typo.. it should be 5063

And yes X_calledIDSpoof is enabled