Hi,
i am trying to set up an OBi 110 as a FXO port for my local asterisk server so i
can use a softphone to callout (not connected to the internet, no router, no gv,
no obitalk, just simple local lan to pstn)
lan
--------------------------
| | |
pstn --- obi 110 asterisk softphone
32bit freepbx distro 4.211.64-1375214241 with asterisk 11, vanilla setup
obi 110, hardware 2.8, software 1.3.0 (Build: 2774), full factory reset
following the instructions from here:
http://wiki.freepbx.org/pages/viewpage.action?pageId=4161594http://www.freepbx.org/support/documentation/howtos/howto-use-an-obi-110-device-to-provide-to-allow-freepbx-to-make-calls-ohttp://www.obitalk.com/forum/index.php?topic=1157.msg7261#msg7261http://tech.iprock.com/?p=3208http://www.obitalk.com/forum/index.php?topic=57.0i am not using GV on Obitalk and have disabled SP1 Service and OBiTALK Service under Voice Services
after closely repeatedly examined each setting on both the device and the pbx.
sofar the folliowing 2 scenarios baffle me:
#1 incoming call from the landline rings the softphone,
picks up the caller id. however, when i answer the softphone,
the other party hears me, but i do not hear themTerminal ID LINE1 SP2
Peer Name <their name>
Peer Number 1yyyyyyyyyy xxxxxxxxxx
Direction Inbound Outbound
21:02:30 Ringing
21:02:35 Call Connected
21:02:51 End Call
netsock2.c: == Using SIP RTP TOS bits 184
netsock2.c: == Using SIP RTP CoS mark 5
app_dial.c: -- Called SIP/6
app_dial.c: -- SIP/6-00000014 is ringing
app_dial.c: -- SIP/6-00000014 answered SIP/OBITRUNK1-00000013
pbx.c: -- Executing [h@macro-dial-one:1] Macro("SIP/OBITRUNK1-00000013", "hangupcall,") in new stack
pbx.c: -- Executing [s@macro-hangupcall:1] GotoIf("SIP/OBITRUNK1-00000013", "1?theend") in new stack
pbx.c: -- Goto (macro-hangupcall,s,3)
pbx.c: -- Executing [s@macro-hangupcall:3] ExecIf("SIP/OBITRUNK1-00000013", "0?Set(CDR(recordingfile)=)") in new stack
pbx.c: -- Executing [s@macro-hangupcall:4] Hangup("SIP/OBITRUNK1-00000013", "") in new stack
app_macro.c: == Spawn extension (macro-hangupcall, s, 4) exited non-zero on 'SIP/OBITRUNK1-00000013' in macro 'hangupcall'
pbx.c: == Spawn extension (macro-dial-one, h, 1) exited non-zero on 'SIP/OBITRUNK1-00000013'
app_macro.c: == Spawn extension (macro-dial-one, s, 42) exited non-zero on 'SIP/OBITRUNK1-00000013' in macro 'dial-one'
app_macro.c: == Spawn extension (macro-exten-vm, s, 14) exited non-zero on 'SIP/OBITRUNK1-00000013' in macro 'exten-vm'
pbx.c: == Spawn extension (from-did-direct, 6, 2) exited non-zero on 'SIP/OBITRUNK1-00000013'
#2 when i dial 81-1-yyy-yyy-yyyy on the softphone, i hear the
softphone rings once and then goes silent. the call terminates by
itself after 30 seconds. the other party says their phone didn't ring. Terminal ID SP2 LINE1
Peer Name
Peer Number xxxxxxxxxx 1yyyyyyyyyy
Direction Inbound Outbound
21:20:01 Ringing
21:20:06 Call Connected
21:20:22 End Call
netsock2.c: == Using SIP RTP TOS bits 184
netsock2.c: == Using SIP RTP CoS mark 5
app_dial.c: -- Called SIP/OBITRUNK1/811yyyyyyyyyy
app_dial.c: -- SIP/OBITRUNK1-00000018 is ringing
app_dial.c: -- SIP/OBITRUNK1-00000018 answered SIP/6-00000017
pbx.c: -- Executing [s@macro-setmusic:1] Set("SIP/OBITRUNK1-00000018", "CHANNEL(musicclass)=none") in new stack
pbx.c: -- Executing [h@macro-dialout-trunk:1] Macro("SIP/6-00000017", "hangupcall,") in new stack
pbx.c: -- Executing [s@macro-hangupcall:1] GotoIf("SIP/6-00000017", "1?theend") in new stack
pbx.c: -- Goto (macro-hangupcall,s,3)
pbx.c: -- Executing [s@macro-hangupcall:3] ExecIf("SIP/6-00000017", "0?Set(CDR(recordingfile)=)") in new stack
pbx.c: -- Executing [s@macro-hangupcall:4] Hangup("SIP/6-00000017", "") in new stack
app_macro.c: == Spawn extension (macro-hangupcall, s, 4) exited non-zero on 'SIP/6-00000017' in macro 'hangupcall'
pbx.c: == Spawn extension (macro-dialout-trunk, h, 1) exited non-zero on 'SIP/6-00000017'
app_macro.c: == Spawn extension (macro-dialout-trunk, s, 22) exited non-zero on 'SIP/6-00000017' in macro 'dialout-trunk'
pbx.c: == Spawn extension (from-internal, 811yyyyyyyyyy, 5) exited non-zero on 'SIP/6-00000017'
What should I try next?
I appreciate your insights and suggestions.
Jake