Hello,
I believe my OBi202 is rebooting upon completion of a call involving my Asterisk server. The scenario plays out like this:
- Use phone on PH1 port of OBi202 to make a call to my cell phone
- Call progresses through my Asterisk server and my cell phone rings.
- I answer the call on my cell phone and notice that no audio is flowing through in neither direction. On the phone connected to the PH1 port on the OBi202, after a few seconds of silence I hear a noise followed by a dial tone.
After configuring the OBi to send syslogs to my server, I'm now seeing what seems to be the OBi rebooting:
[...]
>>>> Phone is ringing
2021-12-01T10:58:22.683507-08:00 obi202 OBi202: TDM_stop_dma: fd #17
2021-12-01T10:58:22.683608-08:00 obi202 OBi202: TDM_stop_dma: done
2021-12-01T10:58:22.684312-08:00 obi202 OBi202: TDM_stop_dma: fd #18
2021-12-01T10:58:22.684410-08:00 obi202 OBi202: TDM_stop_dma: done
>>>> Sometime around here, the call is completed and after a few seconds, I hear the dial tone. I'm going to
>>>> guess the 6sec gap below (between 10:58:30.753138 and 10:58:36.302084) is when that happens.
2021-12-01T10:58:30.253042-08:00 obi202 OBi202: DNS SERVER: 192.168.1.1
2021-12-01T10:58:30.352508-08:00 obi202 OBi202: ==== Networking is ready ====
2021-12-01T10:58:30.352594-08:00 obi202 OBi202: IP Address= 192.168.1.101
2021-12-01T10:58:30.352708-08:00 obi202 OBi202: Gateway = 192.168.1.1
2021-12-01T10:58:30.352864-08:00 obi202 OBi202: Netmask = 255.255.255.0
2021-12-01T10:58:30.352976-08:00 obi202 OBi202: PARAM: Daemon is up ... state: 9 (d7874)
2021-12-01T10:58:30.753138-08:00 obi202 OBi202: PARAM Cache Write Back(256 bytes)
2021-12-01T10:58:36.302084-08:00 obi202 OBi202: BASESSL:Load custom CA certs
2021-12-01T10:58:36.302522-08:00 obi202 OBi202: BASESSL: Can not find custom CA file 0 0
2021-12-01T10:58:36.302718-08:00 obi202 OBi202: ZT: CustomID 1
>>>> HERE IT IS!
2021-12-01T10:58:36.303379-08:00 obi202 OBi202: SYSTEM REBOOTED (lifecycle: 3448)
2021-12-01T10:58:36.338289-08:00 obi202 OBi202: [DSP] MPE init done!
2021-12-01T10:58:36.343359-08:00 obi202 OBi202: [MPM] channel - 0: T.38 Initialization done!
2021-12-01T10:58:36.343701-08:00 obi202 OBi202: [MPM] channel - 1: T.38 Initialization done!
2021-12-01T10:58:36.344253-08:00 obi202 OBi202: [DSP] mpe initialization done!
2021-12-01T10:58:36.347423-08:00 obi202 OBi202: [si3226x] ring amplitude: 70
2021-12-01T10:58:36.347701-08:00 obi202 OBi202: [SLICSI] channel: 0, tx gain: -5, rx gain: -4
2021-12-01T10:58:36.347825-08:00 obi202 OBi202: [si3226x] ring amplitude: 70
2021-12-01T10:58:36.347970-08:00 obi202 OBi202: [SLICSI] channel: 1, tx gain: -5, rx gain: -4
[...]
I'm running firmware 3.2.2 (Build: 8680EX).
Has anyone run into any similar issues?
Thanks!